Beginner's Plumbing: What You Need for Installing a Bathtub
Beginner's Plumbing: What You Need for Installing a Bathtub
Blog Article
We have stumbled on the article on Tools You Need to Install a New Bathtub directly below on the net and think it made perfect sense to talk about it with you on this site.
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and often, tiling skills. Changing an old tub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the job can relocate speedily; if you need to open a wall to get rid of the old bathtub as well as place the brand-new bathtub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old tub as well as embeded in the new one. Ensure you have qualified yourself for the job and also are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your restroom if you have already bought a brand-new bathtub and do not require to change the setup of your previous water system pipelines.
Your tools and also material list should make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Protect the faucet in position with the supplier provided backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former type must be linked to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the called for setting. The wood boards are practical in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the bathtub up until the level reviews degree.
To install taps, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the supply of water as well as examine all joints and also new pipework for leakages as well as tighten them if necessary. Load the bath tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub must wait till the bathtub has been used a minimum of once as this will certainly resolve it right into its last setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make sure that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets unit to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall in between the bath as well as the tiling, leading to complications with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can fracture rather very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been shown that write-up on A Step-by-Step Guide to Installing a Bathtub through someone on our other web property. Enjoyed our blog entry? Please share it. Help others find it. We value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Timely fixes available. Report this page